B832 • 長度單位 Unit of Length (mm) AID LM-SG-SD 快速鑽頭研磨機 LM-SG-SD PORTABLE DRILL BIT RESHARPENINGMACHINE - 一組電源線 - 一組保險絲 - PER20 筒夾 3、4、5、6、7、8、9、10、11、12 共 10pcs( 後夾型 ) ER20 筒夾 13 共 1pcs( 標準型 ) - ER20 夾頭一組 - CBN 鑽石砂輪 #250 砂輪規格 :LM-GW-B250(T) - CBN 鑽石砂輪 #400 砂輪規格 :LM-GW-B400(M) - 六角扳手 4mm、5mm 各一支 -A set of power line -One fuse -PER20 collets 3, 4, 5, 6, 7, 8, 9, 10, 11, 12mm, 10pcs in total (rear clamping)ER20 collet 13, 1pc (standard) -ER20 chuck a set -CBN diamond wheel#250 Wheel spec.: LM-GW-B250(T) -CBN diamond wheel#400 Wheel spec.: LM-GW-B400(M) -An allen wrench of 4mm, & 5mm. 1pc of each -ER20 筒夾 3.5、4.5、5.5、6.5、7.5、8.5、9.5、10.5、11.5、12.5 共 10pcs -SDC 鑽石砂輪 #300 砂輪規格 :LM-GW-S300(N) -ER20 collet 3.5, 4.5, 5.5, 6.5, 7.5, 8.5, 9.5, 10.5, 11.5, 12.5, 10pcs in total. -SDC diamond wheel#300 Wheel spec.: LM-GW-S300(N) 規格 Spec. 研磨範圍 Drill Diameter 先端角 Point Angle 電源 Power 馬達 Motor 轉速 rpm 重量(KGS) Weight LM-SG-313-SD Ø3~Ø13 135° AC110 AC220V 50/60Hz 200W 4500 12.85 如何完成鑽頭研磨前準備 How to prepare for drill grinding A C B D 1. 首先確認鑽頭直徑，再選擇筒夾 直徑 2. 將選擇的筒夾以適當角度崁入筒夾迫緊帽內 3. 鑽頭插入筒夾內，並伸出約35mm左右，但不可鎖緊 4. 筒夾環 套入筒夾 並鎖入筒夾迫緊帽 然後輕輕鎖入並保持鑽頭可用手旋轉 5. 以上步驟即完成鑽頭研磨前準備 一. 鑽頭研磨前準備步驟 Procedures for changing the grinding wheel: 二. 更換鑽石砂輪步驟 Procedures for changing the grinding wheel: A C C B 1.Choose a collet accordingly to the diameter of the drill. 2.Insert the chosen collet into the collet holder at an appropriate angle. 3.Insert the drill through the holder with the tip protruding by 35mm, but do not tighten. 4.Connect the collet nut to the collet which is locked into the collet holder ,then slowly tighten it making sure that you can still turn the drill with your hands. 5.Complete the steps 1 to 4 accordingly for grinding. A C C B B B D 1. 將本機 螺絲全鬆開取下，並將砂輪蓋 掀開 2. 用4mm六角扳手逆時鐘方向將螺絲 鬆開 3. 更換新鑽石砂輪，再將螺絲鎖上即可 4. 將砂輪蓋 蓋上，並將螺絲 鎖緊 注意! 鑽石砂輪螺絲 未鎖緊，砂輪蓋 未蓋好，螺絲 未鎖緊前， 不可將電源打開，以免發生危險 1. Loosen the side knob and open the side cover . 2.Use a 4mm hexagon wrench to loosen the screw ,unscrew it counter-clockwise. 3.Replace a new diamond grinding wheel and tighten the screw after the wheel is installed. 4.Be sure to close the side cover and fasten the side knob properly. Attention! 1.Please make sure that the diamond wheel screw is tightened, the side cover is properly closed, and the side knob is fastened before turning ON the machine, in order to prevent any hazard from occurring. 2.The machine has an automatic ‘power-off’ device that will automatically turn the machine off when the cover is opened. B1 B1 B1 B2 B2 B1 B2 B2 B1 B2 B2 B3 B3 B3 B3 B1 B2 B3 調整後斜角大小 B1 將本機 螺絲全鬆開取下 並將側蓋 掀開 B2 SG-ESS Drills SG7572P 短刃鑽頭專用研磨機 SG7572P Duanren special drill grinding machine ▍標準附件 Standard mating parts ▍特殊附件 Special purpose mating parts 調整靜點大小
RkJQdWJsaXNoZXIy ODM5NzM=