B830 • 長度單位 Unit of Length (mm) AID LM-SG-213 LM-SG 快速鑽頭研磨機 LM-SG PORTABLE DRILL BIT RESHARPENINGMACHINE - ER 筒夾 2.5、3、4、5、6、7、8、9、10、11、12、13mm 共 12pcs - CBN 鑽石砂輪 #200x1pcs(HSS 鑽頭專用 ) 砂輪規格 :LM-GW-B200(B) - 六角扳手 4mmx5mm 各 1pcs - ER collets 2.5 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13mm, 12pcs in total. -CBN DiamondWheel #200*1pc (For HSS drill use). Wheel spec: LM-GW-B200(B) -Hex wrench 4mm*5mm 1pc of each -SDC 鑽石砂輪 #400( 鎢鋼鑽頭專用 ) 砂輪規格 :LM-GW-S400(C) -CBN 鑽石砂輪 #400(4mm 以下 HSS 鑽頭專用 ) 砂輪規格 :LM-GW-B400(A) -ER 筒夾 2.5，3.5mm~12.5mm 11pcs -SDC diamond wheel#400 (for tungsten steel drill use) Wheel spec.: LM-GW-S400(C) -CBN diamond wheel#400 (for use on below 4mmHSS drill use) Wheel spec.: LM-GW-B400(A) -ER Collet 2.5, 3.5~12.5mm, 11pcs in total - ER 筒夾 12、13、14、15、16、17、18、19、20、21、22、 23、 24、25、26mm 共 15pcs - CBN 鑽石砂輪 #200x1pcs(HSS 鑽頭專用 ) 砂輪規格 :LM-GW-B150(J) - 六角扳手 4mmx5mm 各 1pcs - ER collets 12 , 13 , 14 , 15 , 16 , 17 , 18 , 19 , 20 , 21 , 22 , 23mm, 24mm , 25mm , 26mm, 15pcs in total. -CBN DiamondWheel #200*1pc (For HSS drill use). Wheel spec: LM-GW-B150(J) -Hex wrench 4mm*5mm 1pc of each -SDC 鑽石砂輪 #200( 鎢鋼鑽頭專用 ) 砂輪規格 :LM-GW-S200(K) -ER 筒夾 8~12mm，26~30mm -SDC diamond wheel #200 (for tungsten steel drill use) Wheel spec.: LM-GW-S200(K) -ER Collet 8~12mm, 26~30mm ▍標準附件 Standard mating parts ▍標準附件 Standard mating parts ▍特殊附件 Special purpose mating parts ▍特殊附件 Special purpose mating parts 1. 將本機右側旋扭 鬆開，並將側蓋 掀開 2. 用4mm六角扳手逆時鐘方向將螺絲 掀開 3. 更換新鑽石砂輪，再將螺絲鎖上即可 4. 將側蓋 蓋好，並將旋扭 鎖緊 注意! 鑽石砂輪螺絲 未鎖緊，側蓋 未蓋好旋扭 未鎖緊前，不可將電源打 開，以免發生危險 B1 B1 B1 B2 B2 B2 B3 B3 1. Loosen the side knob and open the side cover . 2.Use a 4mm hexagon wrench to loosen the screw ,unscrew it counter-clockwise. 3.Replace a new diamond grinding wheel and tighten the screw after the wheel is installed. 4.Be sure to close the side cover and fasten the side knob properly. Attention! 1.Please make sure that the diamond wheel screw is tightened, the side cover is properly closed, and the side knob is fastened before turning ON the machine, in order to prevent any hazard from occurring. 2.The machine has an automatic ‘power-off’ device that will automatically turn the machine off when the cover is opened. B1 B1 B2 B2 B2 B3 B3 ▍更換鑽石砂輪步驟 ▍Procedures for changing the grinding wheel B1 B3 B2 規格Spec. 研磨範圍 Drill Diameter 先端角 Point Angle 電源 Power 馬達 Motor 轉速 rpm 重量(KGS) Weight LM-SG-213 Ø2~Ø13 85°~140° AC110AC220V( 單相) 200W 6000 9.00 LM-SG-830 Ø8~Ø30 85°~140° AC110AC220V( 單相) 450W 4000 27.0
RkJQdWJsaXNoZXIy ODM5NzM=