A475 AID LM-SG-SD 快速鑽頭研磨機 - 操作說明 LM-SG-SD FAST DRILL RE-SHARPENINGMACHINE - INSTRUCTIONS 1. 將ER夾具組 前端直梢對準後斜角研磨座之凹槽插入 2. 將ER夾具組 上之鑽頭輕輕接觸砂輪並作緩慢進給，壓到底後再作左右旋轉，一直到沒有研磨聲音為止即可 3. 將ER夾具組 取出，轉180°再依上述1、2步驟重複研磨一次即可完成後斜角研磨 1.Insert the collet chuck set by aligning it with the drill center point device. 2.Slowly insert the drill until it touches the grinding wheel slightly, turn it clockwise and counter-clockwise until the grinding sound disappears. 3.Take out the collet chuck set and turn it 180 degrees, and repeat steps 1 and 2 to finish the center point grinding. 1. Check the drill size. 2. Check the Iron filings groove width. 3. Loosen the screws and . 4. The scale moves static point on the seat to a desired size. 5. Then and locking screw fixation can do grind. 1. 先確認鑽頭尺寸 2. 核對排屑槽寬度 3. 將 和 螺絲鬆開 4. 將靜點座 上的刻度移動至所需尺寸 5. 再把 和 螺絲鎖緊固定即可做研磨 1. 先將刻度環 向右轉到底後再向左轉至所要研磨之鑽頭尺寸 2. 將ER夾具組 插入長度設定座 內並將直梢崁入凹槽內 3. 將ER夾具組 向右旋轉至頂住直梢同時將鑽頭向右旋轉至頂住鑽頭刀刃為止 4. ER螺母 向右旋轉將鑽頭夾緊 5. 將ER夾具組 取出確認鑽頭刀刃與ER夾頭之凹槽是否平行，如果沒有平行要重新設定一次 注意! 舊鑽頭少於3/4時，其刻度環調大1-2格 三. 鑽頭長度及角度定位 Setting the drill length and position its movement for drilling: 1.Turn the scale ring all the way clockwise then counter-clockwise to the size of the drill to be grinded. 2.Insert the ER collet chuck set into the preset length slot and push it all the way in. 3.Turn the collet chuck set clockwise until it touches against the pin, and turn the drill clockwise until the cutting edge is felt. 4.Screw the ER collet holder clockwise to tighten the drill. 5.Take out the collet chuck set to make sure the drill’s cutting edge is parallel to the slot of the ER clamping nut. If it’s not, repeat the above steps. Attention: For old used drills with which are now 3/4 of its original length, it is advisable to increase the scale ring by 1-2 mm. B D D D D B D D C1 A1 B1 B1 A2 A1 A2 A1 A2 A1 A2 C1 C2 C2 1. 靜點倒角要大，將 螺絲向順時針 微調至所需之大小 2. 靜點倒角要小，將 螺絲向逆時針 微調至所需之大小 1.To obtain a larger or smaller trimming angle, turn the screw counter-clockwise to increase and clockwise to decrease. E E E 四. 鑽頭靜點研磨 Static point drill grinding: 五. 鑽頭排屑溝寬度調整 Bit chip groove width adjustment: 1. 將ER夾具組 前端直梢對準凹槽插入 2. 將ER夾具組 上之鑽頭輕輕接觸砂輪並作緩慢進給，壓到底後再作左右旋轉，一直到沒有研磨聲音為止即可 3. 將ER夾具組 取出，轉180°再依上述1、2步驟重複研磨一次即可完成鑽頭靜點研磨 1.Insert the collet chuck set by aligning it with the drill center point device. 2.Slowly insert the drill until it touches the grinding wheel slightly, turn it clockwise and counter-clockwise until the grinding sound disappears. 3.Take out the collet chuck set and turn it 180 degrees, and repeat steps 1 and 2 to finish the center point grinding. 六. 鑽頭中心靜點研磨 Center point grinding for drills: 七. 鑽頭後斜角研磨 After bevel grinding drill: 1. 將ER夾具組 前端直梢對準刀刃研磨座之凹槽插入 2. 將ER夾具組 上之鑽頭輕輕接觸砂輪並作緩慢進給，壓到底後再作左右旋轉，一直到沒有研磨聲音為止即可 3. 將ER夾具組 取出，轉180°再依上述1、2步驟重複研磨一次即可完成刀刃研磨 1.Insert the collet chuck set by aligning it with the drill center point device. 2.Slowly insert the drill until it touches the grinding wheel slightly, turn it clockwise and counter-clockwise until the grinding sound disappears. 3.Take out the collet chuck set and turn it 180 degrees, and repeat steps 1 and 2 to finish the center point grinding. 八. 鑽頭刀刃研磨 Blade grinding drill: D D D D D D D D D D D D D D D D D D 向右旋轉束緊 靜點變小 後斜角變小 後斜角變大 靜點變大 輕輕接觸砂輪 整組壓到底 輕輕接觸砂輪 整組壓到底 輕輕接觸砂輪 整組壓到底 左右來回旋轉 左右來回旋轉 左右來回旋轉 向前頂住，向右旋轉 至刀刃卡住設定塊 向前推到底 向右旋轉至檔塊 鬆開 鬆開 鎖緊 鎖緊
RkJQdWJsaXNoZXIy ODM5NzM=