A473 AID LM-SG 快速端銑刀研磨機 - 操作說明 LM-SG FAST ENDMILL RE-SHARPENINGMACHINE - INSTRUCTIONS 1. Place the ER Group fixture alignment of the L-shaped groove, gently insert the contact wheel to do to feed slowly, after the release in the end and make a left and right to move the grinding, polishing has been silent so far to. 2. Remove the ER group replaced a jig is not abrasive blades and repeat the first operation. 3. Keep all blade grinding up. 1. With a 4mm hex wrench Grinder cover around three screws counter-clockwise to loosen the screws 2. Lifting up the cover 3. With a 4mm hex wrench counterclockwise to loosen the screw 4. And then replaced with a new diamond wheel to screws clockwise to lock. 5. The Grinder cover cover, and around three locking to screws. 1. Place the ER Group fixture after insertion bevel seat and align the screw head, gently set into the groove of the clamp and feed has been slow to make up in the end. 2.The ER Group fixture removed and replaced by a non-abrasive blades repeat an action until all blade grinding up. 1.The ER Group fixture aligned recesses edge of seat. 2.Lightly touch the grinding wheel to do to feed slowly so far has been in the end. 3.The ER Group fixture replaced remove a blade, and repeat the operation 1,2, until all blade grinding up. 1. 將ER夾具組 對準 刀口座之凹槽 2. 輕輕接觸砂輪做緩慢進給研磨一直到底為止 3. 將ER夾具組 取出換下一個刀刃，並重複1、2的動作，一直到所有刀刃研磨齊 為止 三. 端銑刀刀口研磨切削 End mill grinding cutting tip: 1. 將ER夾具組 插入後斜角座 並對準螺絲頭，輕輕將夾具組放入凹槽內並作 緩慢進給一直到底為止 2. 將ER夾具組 取出換下一個未研磨刀刃並重複第1動作，一直到所有刀刃研磨齊 為止 四. 端銑刀後斜角研磨切削 End mill after grinding bevel cutting: 1. 將ER夾具組 對準L型之凹槽，插入輕輕接觸砂輪做緩慢進給，放到底後並作 左和右移動研磨，一直研磨到無聲為止 2. 將ER夾具組 取出換下一個未研磨刀刃並重複第1動作 3. 一直到所有刀刃研磨齊為止 五. 端銑刀刀刃研磨切削 End mill grinding cutting edge: 1. 用4mm的六角扳手將磨刀機上蓋周圍的三支螺絲以逆時鐘將螺絲 鬆開 2. 掀開上蓋 3. 用4mm六角扳手逆時鐘將螺絲 鬆開 4. 更換新鑽石砂輪 再將螺絲 以順時鐘方向鎖緊即可 5. 將磨刀機上蓋 蓋好，並將周圍三支螺絲鎖緊即可 六. 更換鑽石砂輪步驟 Replacing the diamond wheel step: 輕輕接觸砂輪，整組壓到底 向下輕輕接觸砂輪，進給一直壓到底 左右來回，移動研磨 螺絲孔 向下輕輕接觸砂輪，進給一直壓到底 B1 H B1 B1 H H H C1 C1 A2 A2 A2 A2 A2 A2 A3 A3 A1 A1 H H H H H H H H H C1 A2 A3 H H A1 如何完成端銑刀研磨前準備 How to prepare for end mill grinding A C B D 向下頂住向右旋轉 至夾頭卡住直梢 向右旋轉束緊 檔塊 1. 先將調整軸 以逆時鐘方向轉至檔塊 的刻度線對準所需之尺寸位置 2. 將ER夾具組 上的半圓槽對準校刀座上的三角點，直放到底 3. 將ER夾具組 向右旋轉至頂住直梢 同時將銑刀過中心之刀刃以順時鐘方向旋轉 至頂住檔塊 為止 4. ER螺母 以順時鐘方向旋轉，將銑刀輕輕夾緊後取出，再用力旋轉緊 1. 首先確認銑刀直徑，再選擇筒夾 直徑 2. 將選擇的筒夾以適當角度崁入筒夾迫緊帽內 3. 銑刀插入筒夾內，並伸出約35mm左右，但不可鎖緊 4. 筒夾環 套入筒夾 並鎖入筒夾迫緊帽 然後輕輕鎖入並保持銑刀可用手旋轉 5. 以上步驟即完成銑刀研磨前準備 一. 端銑刀研磨前準備步驟 Procedures for changing the grinding wheel: A C C B B D 1.Choose a collet accordingly to the diameter of the end mill. 2.Insert the chosen collet into the collet holder at an appropriate angle. 3.Insert the end mill through the holder with the tip protruding by 35mm, but do not tighten. 4.Connect the collet nut to the collet which is locked into the collet holder ,then slowly tighten it making sure that you can still turn the end mill with your hands. 5.Complete the steps 1 to 4 accordingly for grinding. A C C B B 二.端銑刀長度及角度定位 Setting the end mill length and position its movement for drilling: 銑刀向下推到底 向右旋轉至檔塊 直梢 調整軸
RkJQdWJsaXNoZXIy ODM5NzM=