DIN 69871 A133 DAT - 筒夾樣式有彈性、止水、剛性攻牙、伸縮攻牙、極小內孔、燒結式熱 膨脹可供選擇 - 彈性筒夾偏擺精度有標準級 (0.02mm 以內 )，A 級 (0.01mm 以內 ) ，UP(0.005mm 以內 ) - 螺帽預設動平衡設計，可在 RPM10,000 下使用 - 整支通孔，利於出水及抗震 - 如需擋刀螺絲可另外指定 - 裝置時筒夾必須先置入螺帽，再裝入刀具，接著鎖固入本體 - 刀具置入筒夾內孔，必須超出筒夾內孔有效夾持長度，避免不當鎖固， 造成損壞 - 務必使用正確扳手來裝置不可任意改變，避免不當鎖固，造成損壞 -There are various features for collet, like flexibility, water sealed, rigid tapping, extend tapping, minimized inner hole, shrink-fitting for your selection. - The ER collet has three kinds of classes for precision : general class 0.02mm, A class 0.01mm, and UP class 0.05mm. -The pre-balance can reach 10000rpm. -The tool holder is through-hole, which is better for waterto get through and vibration resistance. -Additional selection if stop screw is needed. -When using, please put the collet into the nut and then put them into the body together. -It must exceed the effective clamping length of collet when inserting the cutter into collet to avoid the improper lock & damage. -Please use the right wrench on installation to avoid the improper lock and damage. DAT/ER 立銑刀夾頭 DAT/ER COLLET CHUCK 規格 Spec. l1 l2 d1 d2 T 使用筒夾 Collet 夾持範圍 Clamp Range 重量 (KGS) Weight DAT50 × ER16A - 100 100 70 28 28 M10×1.5P ER16 1~10 3.20 DAT50 × ER16A - 135 135 105 28 28 M10×1.5P ER16 1~10 4.30 DAT50 × ER16A - 160 160 130 28 28 M10×1.5P ER16 1~10 4.50 DAT50 × ER16A - 180 180 150 28 28 M10×1.5P ER16 1~10 4.80 DAT50 × ER20A - 100 100 70 34 34 M12×1.75P ER20 1~13 3.40 DAT50 × ER20A - 135 135 105 34 34 M12×1.75P ER20 1~13 3.60 DAT50 × ER20A - 160 160 130 34 34 M12×1.75P ER20 1~13 3.80 DAT50 × ER25 - 70 70 40 42 42 M16×2.0P ER25 1~16 3.40 DAT50 × ER25 - 100 100 70 42 42 M16×2.0P ER25 1~16 4.15 DAT50 × ER25 - 150 150 120 42 42 M16×2.0P ER25 1~16 4.50 DAT50 × ER25 - 200 200 170 42 42 M16×2.0P ER25 1~16 4.70 DAT50 × ER32 - 80 80 50 50 50 M20×2.0P ER32 2~20 3.60 DAT50 × ER32 - 120 120 90 50 50 M20×2.0P ER32 2~20 3.93 DAT50 × ER32 - 160 160 130 50 50 M20×2.0P ER32 2~20 4.75 DAT50 × ER32 - 200 200 170 50 50 M20×2.0P ER32 2~20 4.90 DAT50 × ER40 - 80 80 50 63 60 M20×2.0P ER40 3~26 3.65 DAT50 × ER40 - 120 120 90 63 60 M20×2.0P ER40 3~26 4.80 DAT50 × ER40 - 160 160 130 63 60 M20×2.0P ER40 3~26 5.20 DAT50 × ER40 - 200 200 170 63 60 M20×2.0P ER40 3~26 5.40 DAT50 × ER50 - 80 80 57 78 - M24×2.0P ER50 5~34 4.85 DAT50 × ER50 - 120 120 99 78 78 M24×2.0P ER50 5~34 5.45 DAT50 × ER50 - 160 160 139 78 78 M24×2.0P ER50 5~34 5.55 DAT50 × ER50 - 200 200 179 78 78 M24×2.0P ER50 5~34 5.70 DIN ISO-15488 PAT NO. M298033 PAT NO. M311791 PAT.NO. ZL200620132661.0 l1 T d2 d1 l2 拉頭Pull Stud 筒夾Collet 螺帽Nut 扳手Spanner A290-A293 A258 A280 A296 ▍特點 Feature ▍選配表 Option
RkJQdWJsaXNoZXIy ODM5NzM=